etc/mkinitcpio.conf

@@ -3,7 +3,7 @@
 # The following modules are loaded before any boot hooks are
 # run.  Advanced users may wish to specify all system modules
 # in this array.  For instance:
-#     MODULES=(usbhid xhci_hcd)
+#     MODULES=(piix ide_disk reiserfs)
 MODULES=()
 
 # BINARIES
@@ -29,32 +29,31 @@ FILES=()
 # 'filesystems' is _required_ unless you specify your fs modules in MODULES
 # Examples:
 ##   This setup specifies all modules in the MODULES setting above.
-##   No RAID, lvm2, or encrypted root is needed.
+##   No raid, lvm2, or encrypted root is needed.
 #    HOOKS=(base)
 #
 ##   This setup will autodetect all modules for your system and should
 ##   work as a sane default
-#    HOOKS=(base udev autodetect modconf block filesystems fsck)
+#    HOOKS=(base udev autodetect block filesystems)
 #
 ##   This setup will generate a 'full' image which supports most systems.
 ##   No autodetection is done.
-#    HOOKS=(base udev modconf block filesystems fsck)
+#    HOOKS=(base udev block filesystems)
 #
-##   This setup assembles a mdadm array with an encrypted root file system.
-##   Note: See 'mkinitcpio -H mdadm_udev' for more information on RAID devices.
-#    HOOKS=(base udev modconf keyboard keymap consolefont block mdadm_udev encrypt filesystems fsck)
+##   This setup assembles a pata mdadm array with an encrypted root FS.
+##   Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
+#    HOOKS=(base udev block mdadm encrypt filesystems)
 #
-##   This setup loads an lvm2 volume group.
-#    HOOKS=(base udev modconf block lvm2 filesystems fsck)
+##   This setup loads an lvm2 volume group on a usb device.
+#    HOOKS=(base udev block lvm2 filesystems)
 #
 ##   NOTE: If you have /usr on a separate partition, you MUST include the
-#    usr and fsck hooks.
-HOOKS=(base udev systemd autodetect modconf keyboard keymap block sd-encrypt lvm2 filesystems fsck)
+#    usr, fsck and shutdown hooks.
+HOOKS=(base udev systemd autodetect keyboard sd-vconsole modconf block sd-encrypt lvm2 filesystems resume fsck)
 
 # COMPRESSION
-# Use this to compress the initramfs image. By default, zstd compression
+# Use this to compress the initramfs image. By default, gzip compression
 # is used. Use 'cat' to create an uncompressed image.
-#COMPRESSION="zstd"
 #COMPRESSION="gzip"
 #COMPRESSION="bzip2"
 #COMPRESSION="lzma"
@@ -65,9 +64,3 @@ HOOKS=(base udev systemd autodetect modconf keyboard keymap block sd-encrypt lvm
 # COMPRESSION_OPTIONS
 # Additional options for the compressor
 #COMPRESSION_OPTIONS=()
-
-# MODULES_DECOMPRESS
-# Decompress kernel modules during initramfs creation.
-# Enable to speedup boot process, disable to save RAM
-# during early userspace. Switch (yes/no).
-#MODULES_DECOMPRESS="yes"

home/default/.config/kanshi/config

@@ -2,7 +2,3 @@ profile {
 	output "LG Electronics LG IPS QHD 201NTPCGD520" enable scale 1.30 position 0,0 mode 2560x1440@60Hz
 	output "LG Electronics LG ULTRAWIDE 0x00000101" enable position 1968,0 mode 2560x1080@60Hz
 }
-
-profile {
-	output "BOE 0x0BCA Unknown" enable scale 1.75 position 0,0 mode 2256x1504@59.999Hz
-}